top of page

Bearings for Brick and Block-Making Machines

Writer: sociocon20
sociocon20
Nov 12
6 min read

A block-making machine is built to shake. The vibration that packs concrete tight into the mould is exactly what makes a good paver or block. But that same vibration runs straight through the bearings, hundreds of cycles an hour, all day long. Pick the wrong bearing for it, and it won't last a season.

Across Karnataka, fly ash brick units, paver block plants and concrete block makers supply the building boom, alongside traditional clay brick kilns. If you own one of these units, this guide shows where the bearings sit, why vibration is their toughest test, and which spares keep the press running.



Bearings for Brick and Block-Making Machines


Why brick and block machines are hard on bearings

  • Vibration. Vibrating tables and shafts shake their own bearings on every cycle.

  • Cement and fly ash dust. Fine, abrasive dust gets into seals and grease.

  • Shock. Hydraulic presses, tampers and mould drops all add impact.

  • Water and slurry. Mixes are wet, and machines are washed down.

  • Outdoor yards. Many units run in open sheds through rain and heat.

Machine by machine: where the bearings sit


Vibrators and vibrating tables — the toughest job

Paver and concrete block machines compact the mix by vibrating the mould. This is done either with vibrator motors bolted to the table, or with vibrating shafts carrying eccentric weights, driven by a motor through belts.

The bearings in these units carry the full force of the unbalanced weights, cycle after cycle. That's why:

  • Vibration-rated bearings matter. In one published case, a block machine's vibration units used ordinary cylindrical roller bearings that were failing every 2 to 3 months. Switching to spherical roller bearings built specifically for vibrating machines solved it.

  • Ordinary motor bearings don't belong here. A home-made vibrator made from a fan or blower motor fails quickly, because those bearings aren't designed to handle unbalance.

  • Loose mounting kills bearings. A loose bolt or missing spring washer on a vibrator lets it rattle, overheat and wear out its bearings.

  • Heat and grease. Vibrating bearings run warm, and losing grease to heat is a common cause of failure. Re-grease on schedule with the right grease.

Pan mixer

The pan mixer blends cement, fly ash, sand, aggregate and water. A heavy vertical shaft turns the mixing arms through a gearbox, so the bearings carry axial as well as radial load — in thick, abrasive mix. Good shaft seals and clean grease are essential.

Hydraulic power pack and press

Hydraulic fly ash brick and block machines run a pump and motor all day. The motor and pump bearings are standard, but they work in dust and heat. See our motor bearing guide and pump bearing guide.

Mechanical presses

Mechanical brick presses use a flywheel, crank and toggle to press the brick. The flywheel and crank bearings take heavy, repeated shock.

Conveyors, feeders and pallet handling

Belt conveyors carry mix to the machine; pallet feeders and stackers move green blocks out. Every pulley and roller runs on pillow block bearings or small sealed bearings, in cement and fly ash dust.

Clay brick plants

Clay brick units have their own set of machines:

  1. Box feeders and roller crushers — heavy shafts and shock loads from stones in the clay.

  2. Pug mills and mixers — paddle shafts in wet, heavy clay.

  3. Extruders — an auger pushes clay through a die. Like any screw press, its shaft pushes back hard on a thrust bearing.

  4. Wire cutters and conveyors — smaller bearings, wet conditions.

  5. Kiln cars and fans — wheels and fans near a hot kiln need heat-rated grease.

Don't forget the belts and couplings

Vibrating shafts, mixers and conveyors are often belt-driven. Keep V-belts at the right tension, replace worn ones as a set, and check alignment after every bearing change. A worn gumboot coupling passes misalignment into both bearings. Kashyap supplies Fenner V-belts, pulleys, universal gumboot couplings and bearing grease alongside bearings.

Seven warning signs to act on

  1. Blocks coming out less dense or with uneven edges — often weaker vibration.

  2. A vibrator or vibrating shaft that's hotter or noisier than usual.

  3. Loose bolts or cracked mounts around vibrators.

  4. A pan mixer that groans or leaks mix at the shaft.

  5. A clay extruder that knocks or heats up at the gearbox end.

  6. Grease turning grey and gritty with dust.

  7. Belts slipping on the vibrator or mixer drive.

Spares worth keeping

  • Vibrator bearings — a full set for each vibrator or vibrating shaft.

  • Pan mixer shaft bearings and seals.

  • Conveyor and pallet feeder pillow blocks.

  • Hydraulic motor and pump bearings.

  • Extruder thrust bearing, for clay brick plants.

  • A written list of every bearing number in the unit.

Buying bearings that last

  • Match the full number — and on vibrators, check for the vibration-rated version of the bearing.

  • Tighten mountings properly when fitting new vibrator bearings.

  • Buy genuine. Fake bearings in copied boxes are a real problem in India — SKF India has raided traders selling counterfeit SKF cartons and duplicate hologram stickers. On a vibrating table, a fake bearing fails very quickly. Ask for a proper GST invoice.

Can't read the number? Send us a photo of the bearing, or the machine make and model, and we'll work out the right part with you before anything ships.

What to do now

Check your vibrator mounting bolts this week, list the bearing numbers on your vibrators and pan mixer, and keep a vibrator bearing set on the shelf.

Kashyap Bearing and Mill Stores has supplied bearings and drive parts from SP Road, Bangalore since 1987 — spherical roller bearings, pillow blocks, thrust bearings, V-belts, pulleys, couplings and grease — and we serve brick and block units across Karnataka. Send us your bearing numbers, a photo or your machine details and we'll confirm the right replacement before it ships. You can also get a quick figure from our bearing price calculator or request a quote through the quotation generator.

📍 #11/1 SP Road, Bangalore 560002

📞 94485 16463 / 89513 22259

đź’¬ WhatsApp us a photo of the bearing or your machine details. We'll confirm the right replacement before it ships.

Frequently Asked Questions on Bearings for Brick and Block-Making Machines


1. Which bearings are used in block-making machine vibrators?

Block and paver machine vibrators carry eccentric weights, so their bearings face heavy, constant vibration. Spherical roller bearings built specifically for vibrating machines usually last far longer than standard bearings here. In one published case, switching from standard cylindrical roller bearings to vibration-rated spherical roller bearings stopped failures that had been happening every 2 to 3 months.

2. Why do my block machine vibrator bearings keep failing?

Common causes are using standard instead of vibration-rated bearings, loose mounting bolts or missing spring washers that let the vibrator rattle, loss of grease from heat, and dust getting past worn seals. Using a fan or blower motor as a vibrator also fails quickly, because its bearings aren't designed for unbalance.

3. Which bearings are used in a pan mixer?

A pan mixer turns its mixing arms on a vertical shaft through a gearbox, so its bearings must carry axial as well as radial load. They work close to thick, abrasive mix, so good shaft seals and clean grease matter. Check the gearbox and shaft bearing numbers on your mixer before ordering.

4. What spare bearings should a fly ash brick or block unit keep?

Keep a full bearing set for each vibrator or vibrating shaft, pan mixer shaft bearings and seals, conveyor and pallet feeder pillow blocks, and hydraulic motor and pump bearings. Clay brick plants should add the extruder thrust bearing. A written list of every bearing number makes reordering fast.

5. Where can I buy brick and block machine bearings in Karnataka?

Kashyap Bearing and Mill Stores at #11/1 SP Road, Bangalore 560002 has supplied bearings and drive parts since 1987 and serves brick and block units across Karnataka, including spherical roller bearings, pillow blocks, thrust bearings, V-belts and grease. Send the bearing number or a photo on WhatsApp at 94485 16463, and the team will confirm the correct replacement before it ships.

 
 
 

Comments


bottom of page