Bearings for Oil Mills: Expellers, Ghanis and Decorticators
An oil expeller works by squeezing. Its screw drives seed forward into a narrowing barrel until the oil runs out — and every bit of that squeezing force pushes straight back along the shaft. Something has to hold that push all day. That something is a bearing.
Whether you run a commercial oil mill with a line of expellers, or a cold-press unit with wooden ghanis, this guide shows which bearings sit where, why the thrust bearing is usually the one that fails, and how to keep the press running.

Why oil mills are hard on bearings
Heavy thrust load. The worm shaft in an expeller pushes backwards with great force. That axial push is the hardest job in the mill.
Heat. Cooking kettles, steam conditioning and the pressing itself all make heat, and it flows into shafts and housings.
Oil, meal and dust. Seed dust, husk and oily meal find their way into every gap. Oil-soaked dust turns grease into sludge.
Long runs. In season, many mills run the presses day and night.
The good news? Most of these positions use standard bearings — thrust bearings, tapered and spherical roller bearings, deep groove bearings and pillow blocks.
The oil expeller: section by section
Worm shaft thrust bearing — the most important bearing in the mill
The worm shaft carries the screw that presses the seed. As the screw pushes seed forward against the choke at the outlet, the seed pushes the shaft backwards. That backward push lands on the thrust bearing, usually at the gearbox end of the shaft.
In screw machines like expellers and extruders, the thrust bearing is commonly the first bearing to fail, because it carries the most load. Depending on the expeller's size and design, it may be a thrust ball bearing, a spherical roller thrust bearing, or a pair of tapered roller bearings.
Signs it's wearing:
Rising noise or heat at the gearbox end of the shaft.
The shaft moving backwards and forwards (end float) when it shouldn't.
Output dropping or the cake getting thicker at the same choke setting.
Related reading: Spherical Roller Thrust Bearings
Gearbox
The gearbox connects the motor to the worm shaft and multiplies torque so the screw can turn under heavy load. Inside are roller bearings on every gear shaft.
Expeller makers advise checking gearbox oil level daily and having the oil checked regularly for metal particles, which can be an early sign of gear wear or bearing failure. When one side of a bearing wears much more than the other, that usually points to thrust load the bearing wasn't designed for.
Related reading: Cylindrical Roller Bearings for Gearboxes
Cooking kettle
Many expellers sit under a steam-heated cooking kettle that conditions the seed before pressing. Its vertical agitator shaft is driven through a gearbox and carries the weight of the stirrer arms along the shaft. That needs bearings that handle axial as well as radial load, plus grease that copes with heat.
Feed screw and drive
The feed screw that meters seed into the press, and the belt or chain drive from the motor, run on deep groove bearings and pillow blocks. An over-tight belt loads the bearing nearest the pulley.
Wooden ghani and cold-press machines
The wooden ghani (kachi ghani, or marachekku) has come back strongly with the demand for cold-pressed oil. A typical machine runs on a 3–5 HP motor. A wooden pestle turns inside a wooden mortar, driven through a gearbox.
The bearings that matter:
Gearbox bearings — they carry the slow, high-torque drive.
The main vertical shaft bearings — they carry both the turning load and the downward force of the pestle.
The motor bearings — standard deep groove ball bearings.
These are small machines, but they often run long hours in small units with no spare machine. Keeping one set of bearings on the shelf is cheap insurance.
Seed cleaning, decorticators and conveyors
Seed cleaners and decorticators
Before pressing, seed is cleaned, and groundnut is shelled in a decorticator. Decorticator rotors and vibrating cleaners run on pillow block bearings, in heavy dust and husk. Sealed inserts and regular cleaning of the housings make a big difference.
Bucket elevators and screw conveyors
Seed and cake move on bucket elevators and screw conveyors — pillow blocks and flange bearings at every head, boot and end. They're easy to forget until one seizes.
Related reading: Flange Bearings for Material Handling Systems · Take-Up Bearings for Belt Conveyors
Filter press and oil pumps
The filter press and the pumps that move crude and filtered oil run on standard pump bearings. Gland leaks that let oil run into a bearing housing should be fixed, not ignored. See Cartridge Bearings for Pumps and Blowers.
Motors
Every machine is driven by a motor on deep groove ball bearings. See our motor bearing guide.
Don't forget the belts, pulleys and couplings
Keep V-belts at the right tension — tight enough not to slip, no tighter.
Replace multi-belt drives as matched sets.
Check pulley alignment after every bearing change.
A worn gumboot (tyre) coupling between motor and gearbox passes misalignment into both.
Kashyap supplies Fenner V-belts, pulleys, universal gumboot couplings and bearing grease alongside bearings.
Seven warning signs to act on
Noise or heat building at the gearbox end of the expeller shaft.
End float — the worm shaft moving in and out.
Output falling, or cake thickness changing, with no change in setting.
Metal particles or darkening in the gearbox oil.
A ghani or kettle that groans or runs rough under load.
Grease turning to black, oily sludge at a housing.
Belts that keep slipping even after tightening.
A thrust bearing that's caught early is a bearing change. One that's left can damage the shaft, the gearbox or the worm — and that's a much bigger bill.
Buying bearings that last
Match the full number — including the suffix on thrust and tapered roller bearings, which often come as matched pairs.
Fit thrust bearings the right way round. A thrust bearing fitted backwards carries no thrust at all.
Choose sealed or shielded bearings where seed dust reaches the shaft.
Buy genuine. Fake bearings in copied boxes are a real problem in India — SKF India has raided traders selling counterfeit SKF cartons and duplicate hologram stickers. On an expeller thrust position, a fake bearing fails fast. Ask for a proper GST invoice.
Can't read the number? Send us a photo of the bearing, or the expeller or ghani make and model, and we'll work out the right part with you before anything ships.
What to do now
Write down the bearing numbers for every expeller, ghani and gearbox in your mill — especially the thrust bearing. Keep one thrust bearing set on the shelf for your busiest press.
Kashyap Bearing and Mill Stores has supplied bearings and mill spares from SP Road, Bangalore since 1987 — thrust bearings, tapered and spherical roller bearings, deep groove bearings and pillow blocks, along with V-belts, pulleys, gumboot couplings and grease. Send us your bearing numbers, a photo or your machine details and we'll confirm the right replacement before it ships. You can also get a quick figure from our bearing price calculator or request a quote through the quotation generator.
📍 #11/1 SP Road, Bangalore 560002
📞 94485 16463 / 89513 22259
💬 WhatsApp us your expeller or ghani details or a photo of the bearing. We'll confirm the right replacement before it ships.
Frequently Asked Questions on Bearings for Oil Mills: Expellers, Ghanis and Decorticators:
1. Which bearing is used in an oil expeller?
An oil expeller's most important bearing is the thrust bearing on the worm shaft, which takes the backward push from pressing. Depending on the machine, it may be a thrust ball bearing, a spherical roller thrust bearing or a pair of tapered roller bearings. The gearbox uses roller bearings on its shafts, and the motor and feed screw use deep groove bearings. Read the exact number off the old bearing.
2. Why does the expeller thrust bearing fail first?
The screw pushes seed forward against the choke, and the seed pushes the shaft back with great force. That axial load lands on the thrust bearing all day, so it carries more load than any other bearing in the press. Heat, oily dust, old grease and a bearing fitted the wrong way round shorten its life further.
3. How do I know my oil expeller bearing is failing?
Watch for noise or heat at the gearbox end of the shaft, the worm shaft moving in and out, output dropping or cake thickness changing at the same setting, and metal particles in the gearbox oil. Catching these early means a bearing change instead of damage to the shaft, worm or gearbox.
4. Which bearings are used in a wooden ghani machine?
A wooden ghani (kachi ghani or marachekku) runs on its gearbox bearings, the bearings on the main vertical shaft that carry both turning load and the pestle's downward force, and deep groove ball bearings in the motor. Sizes vary by maker, so check the old bearings or the machine's manual before ordering.
5. Where can I buy oil mill bearings in Bangalore?
Kashyap Bearing and Mill Stores at #11/1 SP Road, Bangalore 560002 has supplied bearings and mill spares since 1987, including thrust bearings, tapered and spherical roller bearings, pillow blocks, V-belts, pulleys and grease. Send the bearing number or a photo on WhatsApp at 94485 16463, and the team will confirm the correct replacement before it ships.




Comments