Bearings for Dal Mills
Tur dal doesn't come off the emery roll in one go. Pigeon pea usually needs more than three passes before it's fully dehusked — which means the same rolls, elevators and graders handle the grain again and again. More passes, more running hours, more work for every bearing in the mill.
Kalaburagi is known as the tur bowl of Karnataka, and Gulbarga Tur Dal carries its own GI tag. If you own or run a dal mill there or anywhere in the state, this guide walks through the mill machine by machine: which bearings sit where, what wears them out, and how to keep the line running when the new crop arrives.

Why dal mills are hard on bearings
Abrasive dust. Husk, powder and grit from emery rolls are fine and sharp. Past a seal, they grind raceways quickly.
Many passes. Grain goes through dehulling, grading and elevating several times, so every machine runs long hours.
Oil and water treatment. Pitting and oil or water treatment add moisture and oil to the dust — a sticky paste that clogs housings.
Belt drives everywhere. Almost every machine is belt-driven, and an over-tight belt loads the bearing nearest the pulley.
Most dal mill bearings are standard pillow blocks, plummer blocks and deep groove ball bearings. With the right seals, grease and belt tension, they're very manageable.
Machine by machine: where the bearings sit
Cleaners, destoners and graders
The line starts by removing dust, stones and off-size grain with rotary or reciprocating screen cleaners and destoners. Reciprocating and vibrating machines put a back-and-forth load on their drive bearings, which is harder than plain rotation. These usually run on pillow block bearings.
Pitting machine
The pitting machine scratches the husk with an abrasive roller so oil and water can soak in. It's a dusty, abrasive job, and its roller shaft bearings need good sealing.
Oil and water treatment
After pitting, the grain is mixed with oil or water, often in a screw conveyor or mixer, then left to condition or dried. Mixer and screw bearings face oil, moisture and dust together. Shielded or sealed bearings and regular cleaning help.
Dryers
Sun drying stops when it rains, so many mills now use mechanical dryers. Dryer fans and drives run in warm, dusty air and need heat-rated grease.
Emery roll dehuller and splitter — the heart of the mill
This is where the dal is made. Emery-coated rolls rub the husk off and split the grain. The roll shafts run fast in heavy dust, carry belt load, and work through pass after pass. Their bearings — usually pillow blocks or plummer blocks at each end of the roll — are the ones a dal mill owner should watch most closely.
What helps:
Sealed bearings or housings with good seals.
Clean grease, topped up on schedule and never over-filled.
Correct belt tension on the roll drive.
Balanced rolls. A roll with worn or uneven emery coating runs out of balance and shakes its bearings.
Pulse graders
Graders use vibrating trays or sieves to separate whole dal, broken pieces and husk. Their eccentric drives take constant reversing loads.
Polishers
Polishers use a hard rubber roll, leather belts or an emery cone to give the dal its finish. Rubber and leather polishers run fast; emery cone polishers carry load along a vertical shaft as well.
Bucket elevators, conveyors and aspirators
Because tur passes through the dehuller several times, a dal mill has more bucket elevators than you'd expect for its size. Every elevator has a head and boot bearing, usually pillow blocks. Add the aspirator fans that pull husk and powder away, and these are the most numerous bearing points in the mill.
Related reading: Take-Up Bearings for Belt Conveyors · Flange Bearings for Material Handling Systems · Pillow Block Bearings
Motors
Every machine runs on a motor with deep groove ball bearings. See our motor bearing guide.
Don't forget the belts, pulleys and couplings
A dal mill is a belt-driven mill. Belts and bearings fail together:
Keep V-belts at the right tension — tight enough not to slip, no tighter.
Replace multi-belt drives as matched sets.
Check pulley alignment after every bearing change.
A worn gumboot (tyre) coupling passes misalignment into both bearings.
Kashyap supplies Fenner V-belts, pulleys, universal gumboot couplings and bearing grease alongside bearings.
Seven warning signs to act on
A bearing housing on the dehuller too hot to keep your hand on.
A new growl, knock or rumble from a roll, grader or elevator.
More broken dal than usual at the same setting — sometimes a roll running out of true.
Grease coming out as a dark paste of oil and powder.
A belt that keeps slipping or squealing.
A grader that shakes harder or sounds rougher than before.
An elevator that slows or jerks under load.
In season, every lost hour is lost dal. Catch these early and the fix is a bearing, not a breakdown.
Before the new crop: the pre-season checklist
List every bearing number in the mill — cleaners, pitting machine, dehullers, graders, polishers, every elevator head and boot, every fan and motor.
Spin each shaft by hand. Rough or tight spots mean the bearing comes out now.
Clean every housing of old grease and powder, and re-grease with fresh grease of the right grade.
Check belts and couplings and replace tired ones as sets.
Stock the spares that would stop the mill: dehuller roll bearings, elevator pillow blocks and one of each motor bearing size.
Keep the list in the mill office. Next time something fails, send us the number instead of the broken part.
Buying bearings that last
Match the full number, including seal and clearance suffixes. A sealed bearing and an open one are not the same part in a dusty mill.
Match the pillow block insert to its housing, and replace worn housings.
Buy genuine. Fake bearings in copied boxes are a real problem in India — SKF India has raided traders selling counterfeit SKF cartons and duplicate hologram stickers. On a dehuller running all day, a fake bearing fails fast. Ask for a proper GST invoice.
Can't read the number? Send us a photo of the bearing or housing, or the machine make, and we'll work out the right part with you before anything ships.
What to do now
Make the bearing list for your mill before the new tur crop comes in, and keep spares for the dehuller and elevators on the shelf.
Kashyap Bearing and Mill Stores has supplied bearings and mill spares from SP Road, Bangalore since 1987 — pillow blocks, plummer blocks, deep groove bearings, V-belts, pulleys, gumboot couplings and grease — and we serve customers across Karnataka, including Kalaburagi. Send us your bearing list, a photo or your machine details and we'll confirm the right replacements before they ship. You can also get a quick figure from our bearing price calculator or request a quote through the quotation generator.
📍 #11/1 SP Road, Bangalore 560002
📞 94485 16463 / 89513 22259
💬 WhatsApp us your dal mill's bearing list or a photo of the part. We'll confirm the right replacement before it ships.
Frequently Asked Questions on Bearings for Dal Mills:
1. Which bearings are used in dal mill machinery?
Most dal mill machines run on pillow block and plummer block bearings — on emery roll dehullers, pitting machines, graders, polishers and bucket elevator heads and boots — with deep groove ball bearings in the motors and aspirator fans. Exact sizes depend on the machine maker, so read the number off the old bearing or send a photo.
2. Why do dal mill bearings fail so often?
Emery roll dust and husk powder are abrasive, and pitting and oil or water treatment add moisture and oil that turn dust into paste. Tur also passes through the dehuller several times, so machines run long hours. Over-tight belts, unbalanced rolls and old grease make it worse. Sealed bearings, clean grease and correct belt tension prevent most failures.
3. Which is the most important bearing in a dal mill?
The bearings on the emery roll dehuller and splitter. They run fast in heavy dust, carry the belt load, and work through every pass. If they fail, the whole mill stops making dal. Keep spares for these and for the bucket elevator head and boot bearings.
4. How often should dal mill bearings be greased?
Follow the machine maker's schedule and check more often in peak season. Use fresh grease of the right grade, clean out old grease and powder when you can, and never over-fill a housing, because too much grease makes a bearing run hot. A full clean and re-grease before the new crop arrives is good practice.
5. Where can I buy dal mill bearings for Kalaburagi?
Kashyap Bearing and Mill Stores at #11/1 SP Road, Bangalore 560002 has supplied bearings and mill spares since 1987 and serves customers across Karnataka, including Kalaburagi. Send your bearing list or a photo on WhatsApp at 94485 16463, and the team will confirm the correct replacements before they ship.




Comments