Bearings for Elevators and Escalators
A lift rarely fails in silence. Weeks before anything stops, there's usually a sound — a low hum from the machine room that wasn't there last month, or a door that drags on its track. Most of the time, that sound is a bearing.
If you own a factory with a goods lift, manage a commercial building, or run lift maintenance contracts, this guide shows you where every bearing in a lift and an escalator sits, what failure looks like, and how to buy the right replacement without guessing.

A lift is a bearing problem waiting to be heard
Every moving part in a lift turns on a bearing. The motor shaft, the traction sheave, the pulleys the ropes wrap around, the door rollers, the overspeed governor — all of them.
Most of these are standard catalogue bearings. A deep groove ball bearing in a lift motor is the same family of bearing that sits in a pump or a fan. That's good news for you: when one wears out, you aren't always stuck waiting weeks for a branded spare part. You need the right number, the right seal, the right clearance and a genuine brand.
The catch? Lift bearings carry people. So the margin for "close enough" is zero.
Inside the machine room: traction machine and sheave bearings
The traction machine is the heart of a modern lift. A motor turns a grooved sheave, and the steel ropes running over that sheave lift the car and counterweight. Here's where the bearings sit:
Motor shaft → usually a pair of deep groove ball bearings, often with C3 (greater-than-normal) internal clearance so they handle the heat of continuous duty. See our motor bearing guide for how these wear.
Traction sheave shaft → the heaviest load in the lift. Larger machines commonly use spherical roller bearings here, because they carry high radial load and tolerate a little shaft bending. SKF's lift literature recommends open spherical roller bearings for large traction machines. Smaller gearless machines for low and mid-rise buildings often use deep groove ball bearings instead.
Worm shaft (geared machines only) → older geared lifts use a worm and wheel to reduce speed. The worm shaft pushes sideways along its own axis, so it needs tapered roller or thrust bearings to take that axial load.
Brake drum and encoder end → smaller ball bearings, but they still matter. A rough bearing here can upset the brake.
Gearless machines have fewer bearings than geared ones. That doesn't make each one less important — it means each one carries more.
Related reading: Spherical Roller Bearing: The Complete Guide · Cylindrical Roller Bearings for Gearboxes
The bearings people forget: deflector sheaves, doors and governor
The machine room gets the attention. These parts get the breakdowns.
Deflector and counterweight sheaves
Many lifts route the ropes over extra pulleys — a deflector sheave to set the rope spacing, or a counterweight sheave on 2:1 roped lifts. These pulleys usually run on sealed-for-life bearings that can't be re-greased.
This is where a real safety case comes from. Technical Safety BC, the Canadian safety regulator, issued a directive after sealed bearings on a 2:1 counterweight sheave failed. The sheave skewed out of line and pushed sideways against its retainer until the retainer failed. TK Elevator's own bulletin traced the cause to one inner ring wearing faster than the other. The regulator's instruction was simple: inspect sealed sheave bearings on a fixed interval, and replace them as soon as early signs of failure show.
The lesson for any building owner: a sealed bearing has no grease nipple to remind anyone it exists. It needs to be on the inspection list by name.
Door operator and hanger rollers
Lift doors open and close hundreds of times a day. The door hangers ride on small rollers, each with a small sealed ball bearing inside. When those bearings wear, doors drag, jerk, bang or stop short — and a door fault is one of the most common reasons a lift goes out of service.
These are cheap bearings doing heavy, repetitive work. Keeping a few spares is sensible.
Overspeed governor
The governor sheave runs on small ball bearings. It's a safety device, so a stiff or noisy governor bearing should never be left until the next service.
Related reading: Track Rollers and Cam Followers for Sliding Gates — the same rolling idea as lift door hangers.
Escalators: hundreds of small bearings doing the hard work
An escalator is a long, inclined conveyor that carries people. Where a lift has a few critical bearings, an escalator has hundreds of small ones and a few big ones.
Main drive shaft — at the top landing, it carries the sprockets that pull the step chain. It runs in heavy housings, commonly on spherical roller bearings, because it takes the full pull of every loaded step.
Step chain rollers — mounted along the step chain itself. Depending on the design, either these or the step rollers carry the weight of the steps and passengers.
Step rollers — usually a polyurethane or nylon tyre pressed onto a small sealed ball bearing. Each step has its own rollers, so one escalator carries a large number of them.
Handrail drive — drive rollers and pulleys keep the handrail moving in step with the stairs, each turning on ball bearings. The handrail shaft also carries the weight of a cast-iron pulley.
Tension carriage — at the bottom landing, it keeps the step chain taut and runs on its own bearings.
Motor and gearbox — deep groove ball bearings in the motor, plus roller bearings in the reduction gearbox.
When an escalator starts to rumble or a step "clicks" once per loop, it's very often one tired roller bearing among hundreds. Finding it early is cheap. Finding it after the tyre has broken up and damaged the track is not.
Why lift bearings get stricter treatment
A noisy bearing in a factory blower is a maintenance job. A noisy bearing in a lift is a maintenance job and a compliance question.
In Karnataka, lifts and escalators come under the Karnataka Lifts, Escalators and Passenger Conveyors Act, 2012 and its 2015 rules. A lift needs a licence before it can be used, and it is inspected when that licence is renewed. A lift with a known bearing fault that nobody fixed is not what an owner wants an inspector to find.
So three rules make sense for every lift and escalator owner:
Let a qualified lift contractor decide whether a bearing needs replacing — not whoever happens to hear the noise.
Follow the manufacturer's inspection interval for sealed bearings, because they give no other warning.
Never fit a bearing that's "nearly the same". It has to be exactly the same number.
Seven warning signs to act on
Call your lift maintenance contractor if you notice any of these:
A new hum, growl or grinding sound from the machine room or the escalator pit.
The motor or sheave housing running hotter than usual.
Vibration you can feel in the car or through the escalator steps.
Grease leaking, darkening or drying out at a bearing seal — or rust around a sealed pulley.
Lift doors that drag, jerk or stop short. That's very often the hanger roller bearings.
A regular click or knock once per escalator loop, which usually points to a single step or chain roller.
A rope or pulley sitting visibly out of line. Recall the counterweight sheave case above — a skewed sheave is a stop-now sign.
Don't treat these as "next month" problems. A bearing that's noisy today is usually much easier and cheaper to replace than one that has seized.
Buying a replacement that fits first time
Most lift and escalator bearings are standard catalogue items, so you can buy them from an industrial bearing dealer — as long as you match them exactly. Here's what to check:
The full number. Read the number etched on the old bearing's ring. The base number gives the size, but the suffix matters just as much.
Seal or shield. 2RS (rubber seals both sides) and ZZ (metal shields both sides) are not interchangeable in a dusty pit or a sealed-for-life position.
Internal clearance. If the old bearing says C3, the new one must say C3. Motor bearings run hot and need the extra room.
Brand equivalence. SKF, FAG, NTN, Koyo and NBC make the same standard sizes. A like-for-like number from any genuine brand fits the same housing.
Genuine stock only. Fake bearings in copied boxes are a real problem in India — SKF India has raided traders selling counterfeit SKF cartons and duplicate hologram stickers. In a lift, a fake bearing is a safety risk. Buy from a dealer who can give you a proper GST invoice.
OEM-specific parts. Some parts are proprietary assemblies or are still covered by the lift maker's warranty. Replace those the way the lift manufacturer specifies.
Can't read the number? Send us a photo of the bearing, or tell us the lift or escalator make, model and component. We'll work out the correct bearing with you before anything ships.
What to do now
Write down the bearing numbers in your lift or escalator before something fails. Ask your maintenance contractor to note the numbers from the motor, sheaves and door rollers at the next service. Keep that list with the lift logbook.
Kashyap Bearing and Mill Stores has supplied genuine industrial bearings from SP Road, Bangalore since 1987. That includes the deep groove, spherical roller, tapered roller and small sealed bearings used in lifts and escalators. Send us the number, a photo, or the equipment details and we'll confirm the right replacement before it ships. You can also get a quick figure from our bearing price calculator or request a quote through the quotation generator.
📍 #11/1 SP Road, Bangalore 560002
📞 94485 16463 / 89513 22259
💬 WhatsApp us your bearing number, a photo, or your lift make and model. We'll confirm the right replacement before it ships.
Frequently Asked Questions on Bearings for Elevators and Escalators:
1. Which bearings are used in an elevator traction machine?
Most traction machines use deep groove ball bearings on the motor shaft and heavier bearings on the sheave shaft. Large or heavy-duty machines often use spherical roller bearings on the sheave because they carry high radial load and tolerate shaft deflection. Geared machines also use tapered roller or thrust bearings on the worm shaft to take the axial push. The exact numbers depend on the make and model, so always read the number off the old bearing.
2. What are the signs of a failing lift bearing?
Watch for a new hum, growl or grinding sound from the machine room, a motor or sheave running hotter than usual, vibration felt in the car, grease leaking or darkening at a seal, and doors that drag or jerk. Any of these should be checked by your lift maintenance contractor promptly, because some lift bearings are sealed for life and must be replaced, not re-greased.
3. Can a standard bearing replace the one in my lift or escalator?
Often yes, when the bearing is a standard catalogue number such as a deep groove or spherical roller bearing. The replacement must match the full number, including the seal type and internal clearance suffix, and must be from a genuine brand. Proprietary assemblies and parts under an OEM warranty should be replaced as the lift manufacturer specifies.
4. Which bearings are used in escalators?
An escalator uses heavy bearings on the main drive shaft and step chain sprockets, small sealed ball bearings inside the step rollers and step chain rollers, and ball bearings on the handrail drive rollers and pulleys. Because there are hundreds of step and chain rollers on one escalator, these small bearings are the ones replaced most often.
5. Where can I buy elevator and escalator bearings in Bangalore?
Kashyap Bearing and Mill Stores at #11/1 SP Road, Bangalore 560002 has supplied industrial bearings since 1987. Send the bearing number, a photo of the markings, or the lift make and component on WhatsApp at 94485 16463, and the team will confirm the correct replacement before it ships.




Comments