Bearings for Paper Mills
A paper machine is two different worlds joined by one sheet. At the wet end, rolls spin in dripping water and pulp. At the dry end, steam-heated cylinders bake the sheet dry. The bearings at each end face completely different enemies — and a bearing chosen for one end can fail fast at the other.
Karnataka has a long paper history — from West Coast Paper Mills at Dandeli and South India Paper Mills at Nanjangud to the many kraft paper and board mills that supply the state's corrugated box makers. If you run or maintain a paper or board mill, this guide walks through the machine section by section: which bearings sit where, why internal clearance matters so much, and how to plan spares for the shutdown.

Why paper mills are hard on bearings
Water at the wet end. Forming and press sections are wet all the time, so water gets into poorly sealed housings.
Heat at the dry end. Dryer cylinders are heated with steam, and that heat flows through the journals into the bearings.
Thermal growth. Hot cylinders grow in length and diameter. Bearings have to allow for that, or they get crushed.
Continuous running. Paper machines run round the clock between shutdowns.
Section by section: where the bearings sit
Stock preparation
Pulpers, refiners, deflakers, screens and stock pumps prepare the fibre. Refiners run fast with heavy axial loads from the refining plates, so they rely on bearings that take thrust. Pulper rotors and agitators carry heavy loads through gearboxes.
Related reading: Pump Bearing Guide · Spherical Roller Thrust Bearings
Wet end (forming section)
The breast roll, couch roll, table rolls and wire return rolls carry the forming fabric. These rolls run in constant spray, so good sealing is the priority. Bearing makers usually specify standard clearance here, because the rolls run cool.
Press section
Press rolls squeeze water out of the sheet under heavy load. Suction rolls, press rolls and felt-carrying rolls commonly use double-row spherical roller bearings, often with C3 clearance and a tapered bore mounted on a sleeve. Heavy load plus water makes sealing and correct mounting critical.
Dryer section — where clearance matters most
Dryer cylinders are heated by steam from inside, and the heat flows through the journal into the bearing. As the cylinder heats up, it grows. So dryer bearings are set up differently from almost any other machine:
Drive side (locating) — usually a spherical roller bearing that holds the cylinder in position. Paper machine dryer bearings typically have C3 or C4 clearance — extra internal room so they don't tighten up as they heat. FAG's dryer roll example, for instance, uses a 23140 spherical roller bearing with C4 clearance on the drive side.
Front side (non-locating) — a bearing that lets the cylinder grow along its length: a toroidal roller bearing (such as CARB or TORB), a self-aligning cylindrical roller bearing, or a spherical roller bearing free to slide in its housing.
Lubrication — dryer bearings usually run on circulating oil, which carries heat away. Clean, cool oil at the right flow is what keeps them alive.
Felt and canvas rolls and guide rolls in the dryer section use smaller spherical roller bearings, commonly with C3 clearance.
Related reading: Spherical Roller Bearing: The Complete Guide · Spherical Roller Bearing Size Chart · High-Temperature Bearings
Yankee cylinder (tissue mills)
Tissue machines dry the sheet on one very large Yankee cylinder. Its bearings are large, specialist and specified by the machine maker.
Calender, reel and winder
Calender rolls press the sheet smooth, the reel winds the jumbo roll, and the rewinder and slitter cut it into customer rolls. These run on spherical roller and deep groove ball bearings — calender bearings also see heat from heated rolls.
Vacuum pumps, fans and drives
Vacuum pumps, hood fans, cooling tower fans and every motor and gearbox add many more bearings. See our motor bearing guide and Cylindrical Roller Bearings for Gearboxes.
Corrugators and box plants
Downstream, corrugators and box-making machines run corrugating rolls, pre-heaters and conveyors — more heat, more rolls and more bearings. Kraft paper mills and box makers often share the same bearing problems.
Understanding C3 and C4 clearance
The letters at the end of a bearing number matter as much as the numbers. Internal clearance is the small amount of play inside a bearing:
CN — normal clearance, for most general machines.
C3 — more clearance than normal, for bearings that run warm or are fitted tightly.
C4 — more again, for hot positions like dryer cylinders.
Fit a CN bearing where a C3 or C4 was specified, and as it heats up it can lose its clearance, run hot and fail. Always match the clearance suffix on the old bearing.
Seven warning signs to act on
A dryer bearing housing running hotter than its neighbours.
Circulating oil that looks dark, milky or low in flow.
New noise from a press, felt or guide roll.
Water around a wet-end bearing housing.
Rising vibration on a refiner, vacuum pump or fan.
Sheet breaks or wrinkles traced to a roll running out of line.
Bearings creeping on their sleeves or shafts.
Plan spares around the shutdown
List every bearing by number — including clearance and tapered-bore suffixes.
Inspect dryer and press bearings during each shutdown, and check oil system filters and flow.
Order large bearings early. Large spherical roller bearings with C3 or C4 clearance are not always on the shelf.
Keep spares for felt rolls, guide rolls and any roll that stops the machine.
Check sleeves, nuts and housings, not just the bearing.
Keep the list with the maintenance plan for next time.
Buying bearings that last
Match the full number — the base size, the K (tapered bore), the cage, and the clearance (C3, C4).
Use the machine maker's spec on dryer, Yankee and calender positions.
Buy genuine. Fake bearings in copied boxes are a real problem in India — SKF India has raided traders selling counterfeit SKF cartons and duplicate hologram stickers. On a hot dryer cylinder, a fake bearing is a costly risk. Ask for a proper GST invoice.
Can't read the number? Send us a photo of the bearing, or the machine, section and roll position, and we'll work out the right part with you before anything ships.
What to do now
Before your next shutdown, build a bearing list for the machine — section by section, with clearance suffixes — and order the large ones early.
Kashyap Bearing and Mill Stores has supplied bearings and mill spares from SP Road, Bangalore since 1987 — spherical roller bearings with C3 and C4 clearance, plummer blocks, sleeves, deep groove bearings, V-belts and grease — and we serve paper and board mills across Karnataka. Send us your bearing list, a photo or your machine details and we'll confirm the right replacements before they ship. You can also get a quick figure from our bearing price calculator or request a quote through the quotation generator.
📍 #11/1 SP Road, Bangalore 560002
📞 94485 16463 / 89513 22259
💬 WhatsApp us your mill's bearing list or a photo of the part. We'll confirm the right replacement before it ships.
Frequently Asked Questions on Bearings for paper mills:
1. Which bearings are used in paper machine dryer cylinders?
Dryer cylinders usually have a spherical roller bearing on the drive side to locate the cylinder, and a non-locating bearing on the front side — a toroidal roller bearing, a self-aligning cylindrical roller bearing, or a spherical roller bearing free to slide — so the hot cylinder can grow. They typically have C3 or C4 clearance and run on circulating oil.
2. Why do paper machine dryer bearings need C3 or C4 clearance?
Dryer cylinders are heated with steam, and the heat flows through the journal into the bearing. The inner ring heats and expands more than the outer ring, which uses up internal clearance. C3 and C4 bearings start with extra clearance, so they still have enough room when hot. Fitting a normal-clearance bearing there can make it run hot and fail.
3. Which bearings are used in the press section of a paper machine?
Press rolls, suction rolls and felt-carrying rolls commonly use double-row spherical roller bearings, often with C3 clearance and a tapered bore mounted on an adapter or withdrawal sleeve. The press section is wet and heavily loaded, so good sealing and correct mounting matter as much as the bearing itself.
4. What does the C3 or C4 on a bearing number mean?
It shows the bearing's internal clearance — the small amount of play between the rollers and rings. CN is normal, C3 is more than normal and C4 is more again. Higher clearance is used where bearings run hot or are fitted tightly. Always replace a bearing with the same clearance suffix as the old one.
5. Where can I buy paper mill bearings in Karnataka?
Kashyap Bearing and Mill Stores at #11/1 SP Road, Bangalore 560002 has supplied bearings and mill spares since 1987 and serves paper and board mills across Karnataka, including spherical roller bearings with C3 and C4 clearance, plummer blocks and sleeves. Send your bearing list or a photo on WhatsApp at 94485 16463, and the team will confirm the correct replacements before they ship.




Comments