top of page

Bearings for Silk Reeling Machines

Writer: sociocon20
sociocon20
Nov 14
6 min read

A silk filament is finer than a human hair. Reel it smoothly and you get even, strong raw silk. Let a reel jerk, drag or wobble, and the filament breaks, the reeler has to stop and rejoin it, and the day's output drops. Very often, that jerk starts with a bearing.

Karnataka produces about 40% of India's mulberry raw silk, and the reeling belt around Ramanagara, Sidlaghatta and Kollegal is one of the busiest in the country. Ramanagara's cocoon market is often called the largest in Asia. If you run a reeling or twisting unit, this guide shows where the bearings sit in each type of machine, why steam and humidity are their worst enemies, and which spares to keep so the basins never stand idle.

Bearings for Silk Reeling Machines

Why reeling units are hard on bearings

  • Steam and hot water. Cocoons are cooked in boiling water, and multi-end units run steam lines everywhere. Moisture settles on every shaft and housing.

  • High humidity. Reeling rooms are kept humid on purpose. That's good for silk and bad for steel.

  • Long hours. Reeling runs all day, often six or seven days a week during good cocoon seasons.

  • Smoothness matters. A slightly rough bearing that wouldn't matter in a pump can cause uneven tension and filament breaks in a reeling machine.

Machine by machine: where the bearings sit:

Charka

The charka is the simplest reeling device — a large cooking-cum-reeling pan with a hand- or motor-driven reel. It has few bearings, but the reel shaft and drive still run in the steam above the pan. Simple sealed bearings and regular greasing go a long way.

Cottage basin

Cottage basin units separate the cooking basin from the reeling basin. The reels are driven from a common shaft, often through pulleys and belts. The reel shaft bearings and the line shaft bearings carry the load, in warm, damp air.

Multi-end reeling machines

A typical multi-end machine has ten basins, each with around 10–20 ends or reels. That means:

  1. A long line shaft running the length of the machine, held by pillow block bearings at regular intervals.

  2. Reel shafts and gears — dozens of small bearings, each turning a reel of 60–75 cm diameter.

  3. Traverse (croissure and distribution) mechanisms — cams and eccentrics that move the thread back and forth, putting reversing loads on their bearings.

  4. Steam everywhere — boilers supply steam for cooking, reeling and stifling, so every bearing on the machine lives in moisture.

One worn pillow block on the line shaft can make every reel on the machine run unevenly. That's why the line shaft bearings deserve the closest attention.

Automatic reeling machines

Automatic reeling machines add cocoon feeders, end-finding mechanisms, conveyors and many more motors and moving parts. More automation means more bearings — in conveyors, feeders, drives and small motors — and more chances for a single bearing to stop a whole machine. Follow the machine maker's bearing list for precision positions.

Re-reeling machines

Re-reeling machines convert small reels into standard skeins. They have large reels in U-brackets, a traverse mechanism and a drive. The reel bearings run long hours and benefit from sealed bearings and clean grease.

Twisting machines

Twisting (throwing) units twist raw silk into yarn for weaving. Twisting spindles run at high speed, and their bearings decide how evenly the yarn is twisted. Noise, heat or vibration from a spindle is a sign to act.

Boilers, pumps and motors

Boiler feed pumps, water pumps and the motors that drive every machine run on standard deep groove ball bearings. See our motor bearing guide and pump bearing guide.

Beating rust and moisture

In a reeling unit, rust kills as many bearings as wear does:

  • Use sealed (2RS) bearings on reel shafts, line shafts and traverse drives.

  • Consider stainless steel bearings in the wettest positions, right above the basins.

  • Grease regularly with water-resistant grease. Fresh grease keeps moisture out.

  • Protect housings — painted cast iron rusts; keep it painted or use corrosion-resistant housings.

  • Before a long shutdown, run the machines dry, grease the bearings and cover them. Bearings left standing in damp air rust fast.

Don't forget the belts and pulleys

Many reeling and twisting machines are belt-driven. Keep belts at the right tension, replace worn ones as a set, and check pulley alignment after every bearing change. Kashyap supplies Fenner V-belts, pulleys and bearing grease alongside bearings.

Seven warning signs to act on

  1. More filament breaks than usual on one machine, with the same cocoons.

  2. Reels that turn unevenly, jerk or slow down.

  3. A squeak or grinding from the line shaft.

  4. Rust stains around bearing housings.

  5. Grease that looks milky or watery.

  6. A twisting spindle that's noisy, hot or vibrating.

  7. Belts slipping or wearing on one side.

Spares worth keeping

  • Line shaft pillow blocks for each multi-end machine.

  • Reel shaft bearings — a few of each size.

  • Traverse mechanism bearings.

  • Twisting spindle bearings, if you run a twisting unit.

  • Motor and pump bearings for the boiler and main drives.

  • A written list of every bearing number in the unit.

Buying bearings that last

  • Match the full number, including seal type (2RS or ZZ) and any stainless designation.

  • Replace bearings in sets along a line shaft, so the shaft runs true.

  • Buy genuine. Fake bearings in copied boxes are a real problem in India — SKF India has raided traders selling counterfeit SKF cartons and duplicate hologram stickers. In a damp reeling room, a fake bearing rusts and fails fast. Ask for a proper GST invoice.

Can't read the number? Send us a photo of the bearing, or the machine type and maker, and we'll work out the right part with you before anything ships.

What to do now

List the bearing numbers on your reeling, re-reeling and twisting machines and keep a small stock of the line shaft and reel shaft bearings. When the cocoon market is busy, you don't want a basin standing idle for a bearing.

Kashyap Bearing and Mill Stores has supplied bearings and mill spares from SP Road, Bangalore since 1987 — sealed and stainless bearings, pillow blocks, V-belts, pulleys and grease — and we serve reeling and twisting units across Karnataka, including Ramanagara and Sidlaghatta. Send us your bearing numbers, a photo or your machine details and we'll confirm the right replacement before it ships. You can also get a quick figure from our bearing price calculator or request a quote through the quotation generator.

📍 #11/1 SP Road, Bangalore 560002

📞 94485 16463 / 89513 22259

đź’¬ WhatsApp us a photo of the bearing or your reeling machine details. We'll confirm the right replacement before it ships.

Frequently Asked Questions On Bearings for Silk Reeling Machines :

1. Which bearings are used in silk reeling machines?

Silk reeling machines mainly use small deep groove ball bearings on reel shafts and gears, pillow block bearings along the line shaft of multi-end machines, and bearings in the traverse (croissure) mechanisms. Automatic reeling machines add bearings in feeders, conveyors and motors. Because reeling rooms are steamy and humid, sealed or stainless bearings last longest.

2. Why do bearings rust in silk reeling units?

Cocoons are cooked in boiling water, multi-end units run steam lines, and reeling rooms are kept humid for the silk. That moisture settles on shafts and housings and gets past open or worn seals. Sealed (2RS) bearings, stainless bearings in the wettest spots, water-resistant grease and greasing before shutdowns prevent most rust failures.

3. Can a bad bearing cause filament breaks in silk reeling?

It can contribute. A rough or worn bearing on a reel shaft or line shaft can make reels turn unevenly, which changes thread tension. Uneven tension makes fine silk filaments more likely to break. If one machine starts breaking more filaments than others with the same cocoons, check its bearings and belts.

4. What spares should a silk reeling unit keep?

Keep line shaft pillow blocks for each multi-end machine, a few reel shaft bearings of each size, traverse mechanism bearings, twisting spindle bearings if you run twisting machines, and motor and pump bearings for the boiler and main drives. A written list of every bearing number makes reordering quick.

5. Where can I buy silk reeling machine bearings near Ramanagara?

Kashyap Bearing and Mill Stores at #11/1 SP Road, Bangalore 560002 has supplied bearings and mill spares since 1987 and serves reeling and twisting units across Karnataka, including Ramanagara and Sidlaghatta. Send the bearing number or a photo on WhatsApp at 94485 16463, and the team will confirm the correct replacement before it ships.

 
 
 

Comments


bottom of page